We have the new DNA20 Aluminum Box MODS with the Amazing Evolv Chip

dna20-by-picknpuff

You want something that will last and not be scared to use and abuse it.

We have the new DNA20 Aluminum Box MODS with the Amazing Evolv Chip

Put the power and technology into your vaping.

Are you a beginner in using electronic cigarettes or and advanced vaper?

Well it doesn’t matter.

This amazing new design from Pick N Puff is the worlds best product to hit the vaping and e cig market today.

1. Attach your atomizer on the 510 standard connection on the top.

Use with whatever line or brand it may be out there in the endless sea of horrible and great products.

2. Set your wattage to desired power of watts(wattage).

The range is from 7 to 20 watts

3. Our 2400mah Lithium battery will give you endless hrs instead of fussing around with 18 series batteries for your vaping experience.

4. To charge your unit when your battery runs low or completed runs through charge, Plug in USB Micro cable to front of USB port and use any wall usb charger, cell phone charge with usb port or computer and or TV.

DNA20 Box Mod from Pick n Puff Vape Shop Las vegas

Our DNA 20 is a power regulated digital switch-mode DC-DC converter for personal vaporizers.

It features controlled power from 7 to 20 watts, runs from a 2400 mah lithium cell and includes protective features such as over current,

over and under voltage protection as well as thermal shutdown.

Features:

Blue OLED display

Micro USB Internal Charger

Stainless steel buttons for adjustment of watts and power button

synchronous rectification for maximum battery life and minimal heat generation

We put all of this into an amazing construction of aluminum, for the maximum flexion when dropped and knocked.

Built in DNA Charger, which is MICRO USB powered and provides a 500 milliamp charge current.

Battery must be installed in the proper position. + Positive side of battery towards the top of the device.

Damage can occur if the battery is installed improperly.

http://picknpuff.com/wp-content/uploads/2014/01/20140109_012847.jpg

BATTERY INCLUDED:

http://picknpuff.com/wp-content/uploads/2014/01/20140109_011159-464×450.jpg

USERS GUIDE:

Normal Operation Watt setting: The power level currently set on the DNA 20. Battery indicator: The current state of charge of the battery.

Volts display: The current or most recent output voltage being supplied to the atomizer.

Ohms display: The resistance of the atomizer attached to the device. This is measured only when the unit is supplying power to the atomizer. At other times, it shows the most recent measurement.

Other modes

Locked mode: Pressing the fire button five times with less than .7 seconds between presses will cause the device to enter Locked mode. In Locked mode, the device will not fire and the output power will not adjust accidentally. While in Locked mode, the screen will be off, except that pressing a button will show “Locked, Click 5X”. To exit Locked mode, press the fire button 5 times.

Stealth mode: While locked, pressing the fire and down buttons simultaneously for five seconds will switch to stealth mode. In this mode the display is off. It will still show error messages and the “Locked, Click 5X” advisory. To switch back to normal display mode, from locked mode hold down the fire and down buttons simultaneously for 5 seconds. This setting is stored to internal flash memory, and remains if power is removed.

Right Mode and Left Mode: While locked, holding the fire and up buttons simultaneously for 5 seconds flips the display. This setting is stored to internal flash memory, and remains if power is removed.

Error Messages

The DNA 20 will indicate a variety of error states.

Check Atomizer: The DNA does not detect an atomizer, or the atomizer has shorted out.

Shorted: The atomizer or wiring are short circuited.

Check Battery: The battery is below 3.1 volts. It probably needs to be charged.

Weak Battery: The battery sags excessively when firing. This typically means the user is not using a high rate battery, or the battery is old and degraded. It can also mean the battery is not making good contact.

Too Hot: The DNA 20D has onboard temperature sensing. It will shut down and display this message if the internal board temperature becomes excessive.

Too low power setting: The DNA 20D puts out a minimum of 4 volts. With low power settings (7 to 8 watts) and low resistance atomizers (below 2 ohms) the DNA will sometimes be unable to provide a low enough power output to be power regulating. If this is the case, the Ohms display will be flashing. The device will still operate.

Auto power down

The screen will be at full brightness while firing. After 15 seconds with no button presses, the screen will dim. 4 minutes after the last button press, the screen will fade out and the device will go to sleep mode. Pressing any button will turn the device and display back on.

WARRANTY WILL BE VOID IF YOU EXCEED THE OPERATING DISCHARGE TEMPERATURE.

USE AT YOUR OWN RISK.